A check engine light with code P0335 can come with starting trouble, sudden stalling, or an engine that turns over without firing. Those symptoms deserve prompt attention because an unreliable crankshaft signal can interrupt normal engine operation.
However, the code doesn’t automatically mean your Kia needs a new sensor. Wiring faults, poor connections, and problems with the parts the sensor reads can produce similar results. Understanding the difference helps you choose sensible checks and avoid replacing parts without evidence.

What P0335 Means on Your Kia
P0335 means “Crankshaft Position Sensor A Circuit.” Your Kia’s engine computer has detected a problem involving the crankshaft position signal. The exact conditions that trigger the code depend on the engine and model year. For example, Kia’s service information for the 2012 Sportage 2.4L describes a missing crankshaft signal or an incorrect detected tooth count.
The crankshaft position sensor, often shortened to CKP sensor, helps the computer track engine speed and crankshaft position. It reads a rotating target with teeth or slots and produces an electrical signal. The computer uses that information to help control fuel injection and ignition timing. Different engines use different sensor designs, so their test procedures aren’t interchangeable.
Possible symptoms include difficult starting, an engine that won’t start, unexpected stalling, and inconsistent acceleration. Some faults come and go, leaving the vehicle running normally when you finally connect a scanner. These symptoms can also occur with other engine problems, so neither the warning light nor the way the car behaves confirms a failed sensor.
If your Kia stalls, loses substantial power, or runs roughly with a flashing check engine light, pull over safely and arrange assistance. A steady light with normal operation still needs prompt diagnosis. Kia warns that driving with an engine malfunction warning can involve a risk of catalytic converter damage and reduced engine power.
Kia Error P0335: Common Causes
Several faults can interfere with the crankshaft signal before it reaches the engine computer. The following causes are useful starting points, but testing must establish which one applies to your Kia.
1. A Failing Crankshaft Position Sensor
The sensor itself can develop an internal electrical fault or suffer damage that prevents it from producing a usable signal. Significant heat exposure and damage to its sensing surface are established reasons for sensor failure.
An intermittent complaint needs careful attention to when it happens. Note whether starting trouble occurs before the first trip, after driving, or following a brief stop. That pattern gives the technician useful conditions to reproduce, although it doesn’t establish that the sensor is defective.
The strongest evidence comes from checking the signal using the correct procedure for your engine. Kia’s diagnostic information for the 2008 Rio 1.6L includes waveform testing and checking operation with a known good sensor when appropriate. A code description alone isn’t the same as that confirmation.
2. Damaged Wiring or Poor Connector Contact
A working sensor can still appear faulty if its signal can’t travel through the wiring. A broken wire interrupts the circuit, while damaged insulation can allow an unwanted electrical connection. Loose or corroded terminals can also prevent reliable contact.
Kia’s 2010 Forte 2.0L diagnostic procedure specifically calls for checking connectors for looseness, bending, corrosion, contamination, and damage. It also separates power, ground, and signal circuit checks rather than treating every circuit problem as a sensor failure.
3. A Fault in the Sensor’s Power or Ground Circuit
Depending on its design, the crankshaft sensor may require an external power supply and ground connection. If either is interrupted, replacing the sensor won’t restore normal operation. The supporting circuit needs repair.
For example, the service procedure for the 2006 Sportage 2.7L directs technicians to investigate the supply circuit, main relay connection, and specified sensor fuse when sensor supply voltage is missing. It separately checks the ground circuit. Those instructions apply to that configuration, not every Kia.
Several electrical codes appearing together make it especially useful to review the complete scan report. However, multiple codes don’t prove that a shared fuse, ground, or power feed has failed. The wiring diagram and circuit tests must show whether the affected components have a connection in common.
4. Target Wheel Damage or Incorrect Sensor Clearance
The sensor needs a readable rotating target and the correct distance from it. Mechanical damage to the target, contamination from metal particles, or an installation problem can interfere with the signal even when the sensor’s electronics work. HELLA identifies encoder wheel damage and metal contamination among established crankshaft sensing faults.
Recent repair history can be valuable here. Kia’s 2008 Sportage 2.7L procedure includes checking sensor clearance and crankshaft to camshaft synchronization when indicated. These are professional checks because the location, measurements, and required access vary by engine. P0335 alone doesn’t prove that your timing system or target wheel is damaged.
Kia Error P0335: DIY Fixes
Safe troubleshooting starts with preserving the fault information and looking for accessible clues. The checks below can help narrow the problem, while electrical testing and repairs should follow the service information for your exact Kia.
1. Record the Complete Scan Report
Park safely, apply the parking brake, and follow your scanner’s connection instructions. Read all available engine codes rather than stopping after P0335. Save photographs or a report showing the code descriptions and whether the scanner labels them current, pending, stored, or permanent.
Also save any available freeze frame data. This is a snapshot of operating conditions recorded around a fault event. Don’t clear the codes first, because a scanner’s erase function can remove useful diagnostic information and reset emissions monitor results.
Alongside the scan report, write down what you noticed. Useful details include whether the engine stalled, whether it restarted, and whether the problem appeared before or after recent repairs. This step won’t repair a failed component, but it gives the next checks a clear starting point.
2. Look for Accessible Wiring Damage
With the engine off and cool, use a flashlight to examine wiring that you can see safely from above. Consult information for your exact model before identifying the crankshaft sensor. Its location can differ substantially between engines.
Look for a connector that appears separated, a broken retaining clip, damaged protective covering, or wiring rubbing against a nearby part. Photograph anything suspicious. Keep your hands away from fans, belts, and hot parts, and don’t crawl underneath a vehicle supported only by a jack.
Limit this check to observation if reaching the sensor requires removing parts or working near exposed wiring. Don’t pull on wires, insert objects into terminals, or use a running engine to test a loose connection. Visible damage is a reason for a proper connector or harness repair, followed by verification that the fault is gone.
3. Match Any Fuse Check to Your Owner’s Manual
If your owner’s manual identifies a relevant fuse and provides a user replacement procedure, follow that guidance with the vehicle switched off. Use only the specified fuse type and rating. A fuse number or rating quoted for a different Kia may have no relevance to yours.
A replacement fuse may restore an interrupted supply, but it won’t correct the condition that caused the fuse to fail. If it blows again, stop replacing it and arrange electrical diagnosis. Never fit a larger fuse or bypass it. Kia’s Sportage diagnostic procedure treats a blown sensor fuse as part of a supply circuit investigation.
4. Have the Sensor Tested Before Authorizing Replacement
If the initial checks don’t identify the fault, ask for testing of the sensor and its supporting circuits. Useful diagnosis should distinguish a missing sensor output from a signal lost in the wiring. That distinction matters because either fault can leave the computer without usable crankshaft information.
Avoid applying a generic resistance test or an online voltage specification to an unidentified sensor. HELLA cautions that sensor type must be established before testing and that an unsuitable resistance test can damage a Hall type sensor. Leave powered circuit measurements and waveform testing to someone with the correct equipment and service information.
5. Check Repair Details if the Code Returns
If P0335 appeared immediately after sensor replacement or another repair, give the shop that history before authorizing another part. Ask it to verify the replacement sensor’s application, connector engagement, wiring placement, and mounting. The review should focus on what was disturbed and whether installation matches the engine’s requirements.
Correct mounting matters. DENSO’s installation guidance calls for the vehicle manufacturer’s tightening torque and proper clearance between the sensor and rotating target. A part that plugs into the connector still needs to be the correct part and installed properly.
Don’t assume every Kia needs a crankshaft sensor relearn after replacement. Kia bulletin PS417 concerns P0315 on specified 3.3L GDI engines and calls for different action depending on the signal pattern. It isn’t a universal P0335 reset procedure. Any required relearn should come from the service instructions that apply to your vehicle.
6. Contact a Qualified Automotive Technician
Arrange professional diagnosis if your Kia won’t start, stalls unexpectedly, or continues to set P0335 after the accessible checks. Seek help immediately when the vehicle’s behavior makes driving unsafe. Repeated starting attempts or trips intended to reproduce a stall aren’t a useful substitute for controlled testing.
Bring the scan report, symptom notes, and recent repair details. Ask the technician to explain the evidence supporting the proposed repair. Depending on the findings, the work may involve a connector, wiring, sensor, supply circuit, or a mechanical inspection. Kia’s diagnostic procedures support checking these areas in stages rather than replacing everything associated with the code.
After repair, ask how normal operation was verified, especially if the complaint was intermittent. A permanent code, where supported, can remain until the vehicle’s own monitoring confirms the repair. Bosch explains that permanent codes are cleared by the vehicle rather than the scanner’s erase command, so their presence alone doesn’t establish that a replacement part failed.
Wrapping Up
P0335 gives you a useful starting point, but the right repair depends on where the crankshaft signal is being interrupted. Recording the symptoms and keeping the original scan information helps you make better decisions before spending money on parts. Your Kia’s model, year, and engine also matter when choosing any test or repair procedure.
Start with the safe checks you can complete comfortably. If the engine stalls, won’t start, or the fault returns, arrange qualified diagnosis and bring your notes. Clear evidence makes the next repair decision much easier.