How to Easily Reset Transfer Case Control Module Silverado

How to Easily Reset Transfer Case Control Module Silverado, If you drive a Chevy Silverado, you know that you need to keep your transfer case control module in working order. But if ever you came across a transfer case control module that went out, don’t worry! You can easily reset it without taking your vehicle to your mechanic.
In this article, we will walk you through the reasons for the faulty operation of the transfer case control module and the process for resetting the transfer case control module on a Silverado.
If you cannot identify what is wrong with your vehicle and you suspect the problem to be in your car’s software, navigate to this site for instructions.

The transfer case module is malfunctioning.
Power Surge:
One possible reason for your application is preventing because of a power outage. This can happen if the battery develops a fault, the power is a boomer, and the product is plugged in. Then, if the eggs establish again, a surge of energy could result.
Wiring Problem:
Another reason the module might stop working is a problem with the wiring related to the module transfer case. This could happen if the wires connecting the module to the transfer case are loose or damaged.
Module Failure:
The module may cease functioning over time, and this may be due to heavy use and wear. On the other hand, you may be capable of preventing the problem.
Water Damage:
If the module becomes wet, it begins to malfunction. If this happens in a vehicle, it could happen if it is driven in the rain or if water somehow enters the unit.
Physical Damage:
The module may become damaged if it is dropped or dropped. This can be exacerbated if the device by itself receives damage.
Temperature Change:
The module may shut down in winter or summer if the vehicle is accidentally exposed. This could be caused by extreme heat or extreme cold.
Read More: HOW OFTEN TO CHANGE FUEL FILTER ON 6.7 POWER-STROKE
We should reset the transfer control module before we can be sure it functions correctly.
The transfer case control module is responsible for controlling the transfer case, which is the part of a large truck that helps to change gears. If the transfer case control module goes out, the car will not be able to function or change gears properly. For this reason, you should regularly check its operational efficiency.
How to identify if the module needs to be reset?
- Engine Light must be turned on: when the module fails. It shows there’s something wrong with the car. Of course, it’s best to have a vehicle technician check the malfunction as soon as possible.
- If the 4WD system is not working accurately & correctly, if the 4WD system is not working, the 4WD light will come on. This is a sign that the module must be reset.
- If you hear a strange noise starting when you begin your truck, this is another indication that something is wrong with the module.
- If the transfer case control module were to malfunction, the truck might not correctly shift.
- The module is getting hot to the touch. It indicates that the module should be reset if it’s getting hot to the touch.
- The burning smell from the transfer case module indicates a fault with the transfer case control module that must be repaired.
Do you need to check to ensure the module is working correctly often?
The module should be checked a minimum of once every three months when comparing its operating status with a mechanic. In particular, pay attention to irregularities that seem to stem from the transmission or sensitive parts of the engine.
What should you do if the transmitting case control module is not working correctly?
If your transfer case control module stops working, don’t panic! You can solve it yourself, without taking the motor vehicle to the mechanic.
Here’s what you’ll need to do:
Start by disconnecting the battery: It will certainly ensure that no energy goes into the case module to avoid additional harm. It will also help ensure that no electrical wiring is provided to the transfer case module.
Next Step, remove the module from the transfer case: The brakes will be held in place by four bolts. You must have a socket wrench to remove them. You will also need a screwdriver.
Take the module apart: When you have removed the module from the transfer case, you’ll need to take the case apart. This is usually a straightforward matter of screwing a few screws.
Dry the module: If the module is wet, it is best to use a blow-dryer to dry it off.
Put the module back together: Once it is dry, you can put it back together.
Reconnect the battery: At the end of the excursion, reconnect the battery and turn on the truck. The trailer module should now be reactivated and working correctly.
Reactivate the solar panel and turn the trailer on at the end of the excursion. The module for the trailer should now be reactivated and working.
Effects of not resetting it include difficulty accessing it.
If you don’t take care of the settings module, your vehicle may have issues with its 4WD system. For example, if the set module is not functioning correctly, it may result in your car being stuck in 4WD mode and not being able to shift to 2WD. Additionally, if the set module is not reset, it could cause your vehicle to have an issue shifting gears or experience other transmission problems.
Method 1: The Easy Ways to reset the transfer case control module
[su_note note_color=”#fafadd”] It is called the easy way because you won t need to purchase additional equipment to reset the transfer case control module. Instead, follow these steps and wait for the result. 1.First of all, it is important to turn the key. It will not make sense if you proceed with this method without turning the key. When the key is secured, then you will proceed to the next step. 2.Afterward, you have to hit the accelerator turn knob for a few moments. It does not need to be a lengthy period, so five minutes to ten minutes is fine. At this time, the accelerator is checking the transmission functionality. 3.You can release the accelerator pedal and turn off the ignition key in order to turn off the gas pedal. The gas pedal’s job is mainly to accelerate the combustion of fuel. When a procedure to reset the TCCM needs to be performed, the accelerator pedal has to function correctly. 4.Again, it’s time to wait for a while until completing the process from step 1. After a near instant, repeat step one. 5.If you run the process two or three times, your TCCM should be ready to perform. [/su_note]
Read More: HOW TO UNLOCK A CHEVY TRUCK WITHOUT KEYS
Method 2: Using the Jumper Cables
Removing the jumper wires is the universal strategy to bring all your vital operational modules to their initial state. In addition, it is commonly serviceable for most cars. Here is how you can do this.
1. You can begin by removing the negative battery cable using a screwdriver. Do not let the cable fall anywhere in the engine. You need to take the tape off the cable head into the machine, or you can receive a trickle charge to any metal that comes in contact with the metal.
2.A cover that’s clean and dry prevents the item from coming into contact with materials and metal.
3.Connect the opposing end of the jumper cable to the battery’s negative and the positive end to the battery’s positive. Then, let the line stand for a while. It doesn’t matter whether you wait five minutes or 30 minutes.
A significant experience or choice will aim to drain the battery and ECUs. Otherwise, they will seek to run the alternative route to the ground, assuming it remains available.
4.Wait until the battery has entirely run down, then cut and remove the jumper cable and rag. Please put it in its proper place to ensure an opposing end.
5.Wait until the vehicle has cooled before turning the key to start the motor vehicle. Allow it to run slowly, with its ignition on, for 10 to 15 minutes. During this period, the vehicle’s program will regenerate automatically.
6. Now, enter the ignition key and turn the key to the “on” position, which is primarily a cycle. You are tinkering with the car’s ignition and engine for five to ten minutes. Afterward, you can monitor the idling feature and leave it as so. Remember not to activate additional parts since they will draw in more electrical power. Wait to check whether your engine is idling appropriately.
7.It’s time to run the controls and scan the sensors to ensure they function. Repeat the procedure from the previous measure three times if you find any defects. Then your car will be easily ready for the next several hundred miles.
Read More: HOW TO GET AIR OUT OF BRAKE LINES WITHOUT BLEEDING
Method 3: Using the TCCM Fuse
In this method, you never require any accessories to reset the code. You only have to use the fuse and reset the TCCM.
1.Turn off the circuit breaker at the base of the fuse box in any section of the device in question, then pull up the fuse from the box.
2.Now it s the waiting time up to that point. In the meantime, the fuse box ensures that there s no connection between the accelerator and the control module.
3.Check whether the fuse is working by looking out at it. If it is, then exchange it for a functioning one and place it in the fuse box.
4.After that, you can turn on the ignition key and run the engine.
5.You will see your headlights blinking. This notification will come when your vehicle’s active cruise control has completed the reset. After that, start your engine, shut down, restart five times, and turn off the engine.
6.Finally, you should check whether the engine is running properly. Turn the engine on and determine which RPM or idling points the engine is working at. You may also check to make sure that the transmission or driveshaft is running smoothly.
Final Conclusion for How to Easily Reset Transfer Case Control Module Silverado
The transfer case control module in Silverado can malfunction due to several causes. They include the check engine light being on, the transfer case making a squealing noise, the truck not shifting properly, the 12V electric outlet getting warm to the touch, and a burning smell from the module.
If you see any of these symptoms, resetting the appliance is always a good idea. Resetting the procedure is simple only because there are no complex steps to follow.
Possibly causing the truck to get stuck in four-wheel drive mode and not shifting to four-wheel drive is why not resetting this component could lead to precisely that. Furthermore, it could also cause issues shifting the truck’s gears and perhaps even cause the transmission to fail to operate correctly.
So it should be better to go back on the off chance the challenge wasn’t played through the entire match. We hope this post helped you alot better and understand the delicate role of resetting the transfer case module in your Silverado pickup. Thanks for reading!